RCBS

• Holds cases in all RCBS.
• Can hold cases in other presses.
• Fits RCBS hand priming tool.

• Full length sizer die.
• Features expander - decapping unit.
• Also includes seater die with bullet seater plug.

• RCBS Reloader Special Dies
• RCBS Cowboy Dies
• All RCBS "Precision" Dies with the following exceptions: 6mm PPC, 7mm TCU, 35 Whelen, 357 Sig, 358 Winchester/356 Winchester, 416 Remington Magnum

A reloader never knows when a part might break. Be prepared for anything with high quality factory replacement parts that will have your RCBS Reloading Dies sizing and depriming running like the day they were taken out of their packaging.

Technical Information

Fits:

• RCBS Reloader Special Dies
• RCBS Cowboy Dies
• All RCBS "Precision" Dies with the following exceptions: 6mm PPC, 7mm TCU, 35 Whelen, 357 Sig, 358 Winchester/356 Winchester, 416 Remington Magnum

• A non-toxic, water-soluble lubricant.
• Wipes off easily, leaving no sticky residue.
• Will not harm primers. 2 oz. bottles.

• Fastest way to feed powder to your scale.
• Large-capacity reservoir and extra-wide base for stability.
• Perfect height for all powder scales.

• Pointed end used to remove burrs.
• Features a bevel inside the case.
• Fit the open end over the case mouth to remove exterior burrs.

• Stainless steel bristles.
• Features interchangeable mounts for large and small primer pockets.
• Includes no roll accessory handle.

• Eliminates the need for holders for each cartridge.
• Includes a primer seating safety gate.
• Screw-in primer seat plugs.

• Brushes remove dirt and powder from the inside of case necks.
• Lightly lubes the inside of the neck for better expanding.
• Calibre: .270-.30.

Spare Decapping rod with expander ball

Spare Decapping rod with expander ball

• pad can be removed from the sealable storage case for easy cleaning

• Remove burrs left inside flash hole during manufacturing.
• Tool automatically locates the hole and quickly removes the burr.
• Specify Calibre - .22, 6mm, 7mm .30 cal when ordering.

• Complete kit will properly clean and lube cases for resizing the simple way.
• Includes Case Lube Pad and 2-ounce bottle of Case Lube-2.
• Has accessory handle with two interchangeable Case Neck Brushes for 22-30 calibers.

• Fits: RCBS Pow'r Pull Impact Bullet Puller
• Function: Replacement three-jaw chuck assembly
• Material: Aluminum

• Use with the Uniflow Powder Measure.
• Provides much more consistent loads.
• Controls the gravity feed pressure of the powder column on the metering unit.

Standard Bullet Puller Collet

• Designed with a taper to guide pilot into the case mouth
• Prevents case from wobbling when trimming case to length

The case trimmer pilots designed with a taper to guide pilot into the case mouth and guides cutting blades to prevent deformation.  

In short order, separate the cleaned cases from the cleaning media. Merely empty the cases and media from the case cleaner into the separator basket. With several turns of the basket handle, the media falls to the bottom of the separator, leaving the cases clean and ready to use. The fine dust from the media is trapped inside the separator.

• Brushes remove dirt and powder from the inside of case necks.
• Lightly lube the inside of the neck for better expanding.
• Calibre: .22 - .25.

• Features a specially designed drop tube.
• Helps avoid any messy powder spills.
• Avoids spills around case mouth.

• This bullet puller makes it easy to recover all your components or salvage the parts from unknown or old reloads.

The RCBS Electronic Scale Powder Pan is a great replacement pan for any reloader looking for a pan with an integrated powder funnel for their electronic scale.

• Easy way to fix mistakes.
• An improved 3-jaw chuck firmly grips the case rim.
• Guaranteed for life.

• Holds 50 cases.
• Keeps cases steady at all times.
• Also comes as part of the Rock Chucker Spreme Master Reloading Kit.

The RCBS® Primer Catcher keeps spent primers off the floor when ejected from fired cases. A plastic clip holds the Primer Catcher snug and secure to press, yet it's easily removed for emptying. It's compatible with the Rock Chucker®, JR and Reloader Special presses only.

Separates clean cases from dry media in seconds.

• Eliminates the muscle fatigue associated with long hours of tightening a T-bar.
• Keeps cases securely locked in place and aligned with the cutter.
• Made of die cast metal with hardened cutting blades for a lifetime of reliable use.

7mm bullet puller  collet

• Large ergonomic design
• Can be used with many RCBS accessories